Are you ready to create stunning resin art or durable, high-gloss tabletops? ProGlas 1000 is here to help! This premium-grade epoxy resin is perfect for crafting flawless table tops, bar tops, and resin art projects. With its deep, glass-like shine and enhanced UV resistance, ProGlas 1000 protects against yellowing and sun damage while delivering a professional finish. With an extended working time of up to 50 minutes in the mixing container and around an hour on the surface (at 70°F), ProGlas 1000 is user-friendly and perfect for both experts and DIY enthusiasts.

To ensure the best results with this resin, follow our comprehensive guide packed with preparation tips, essential supplies, and troubleshooting advice.

Note: ProGlas 1000 is not suitable for freezing climates, as low temperatures may lead to de-lamination.

Preparation

Proper preparation is crucial for a successful epoxy project. Follow these steps to get started right:

1. Warm the Resin: ProGlas 1000 works best at 75–80°F. If Parts A and B have been stored in cold environments like a garage or basement, they might have crystallized. This could also happen during shipping of the product. Warm them in a water bath before use to achieve optimal performance.
2. Check Room Temperature: Ensure the area you’re working in is between 75–80°F to promote even curing.
3. Prepare the Surface: Clean the surface thoroughly to remove dust, oil, and debris. A clean, smooth surface helps the resin adhere and guarantees a flawless finish.

Supplies You’ll Need

• Mixing cups: Graduated cups for precise 1:1 mixing by volume.
• Stir sticks: Tongue depressors or paint stir sticks work great!
• Spreader or squeegee (optional): For even coverage.
• Heat gun or torch: Essential for removing air bubbles.
• Drop cloth: Protect your workspace from drips.
• Level: Ensure your surface is even.
• Respirator and gloves: For safety while working with resin and handling fumes.

Step-by-Step Application

1. Measure and Mix

• Combine equal parts (by volume) of Part A and Part B into two separate graduated cups. Accurate measurement is crucial!
• Use a stir stick to mix thoroughly. Scrape the sides and bottom of the mixing cup to ensure the resin is well-mixed. The mixture will appear hazy at first but should clear up after 3–4 minutes of mixing.

Pro Tip: If the resin feels thick like molasses or contains crystals, it’s too cold. Warm it before mixing!

2. Seal Coat (Optional but Recommended)

• Apply a thin seal coat by pouring a small amount of resin onto the surface and spreading it with a foam brush or squeegee.
• Allow the seal coat to cure for approximately 4 hours before applying the flood coat. This step helps prevent bubbles during the flood coat process.

3. Flood Coat

• Pour the mixed resin gently along the length of your surface, allowing it to self-level.
• Keep the flood coat approximately 1/8" thick. If you need multiple layers for added thickness, allow each layer to cure for 4–6 hours before pouring the next layer.

Important: Pouring too much resin at once can generate excess heat, causing a messy outcome. Work in thin layers!

4. Eliminate Bubbles

• Hold a torch or heat gun 6–8 inches above the surface and wave it gently to burst bubbles. Repeat as needed until the surface is clear. Be very careful on this step.

5. Curing

• Keep the room temperature steady between 75–80°F while the resin cures. ProGlas 1000 typically becomes tack-free within 12 hours and fully cures in 3 days.
• Avoid lowering the temperature, as it can extend curing time or prevent the resin from fully hardening.

6. Final Touches

• Check the bottom edges of your project after curing. Any drips that formed can be removed cleanly once the resin has set.
• Once cured, sit back and enjoy your beautiful creation!

Troubleshooting Common Issues

Here are some tips to fix common resin issues and ensure perfect results every time.

• Sticky Spots in Cured Resin: Sticky areas usually result from improper mixing or incorrect ratios. Always measure ProGlas 1000 exactly at a 1:1 ratio by volume and mix thoroughly, scraping down the sides and bottom of the cup.
• Quick Curing: Resin cures too fast if mixed for too long, mixed aggressively, or left in the mixing container for extended periods. Avoid working in large batches, as the chemical reaction generates heat naturally.
• Air Bubbles Stuck in the Surface: If air bubbles don’t rise to the surface, your resin may have been too cold when mixed. Always pre-warm the resin to 75–80°F, and use a heat torch to aid the bubbles’ escape.
• Crystallized Resin: If your resin is clumpy or gritty, it has likely crystallized due to cold temperatures. Warm the jugs in a water bath at 120°F, stirring occasionally until the crystals dissolve.

Create Stunning, Long-Lasting Creations

By following these steps and tips, you can achieve flawless, professional-looking resin creations with ProGlas 1000. Whether you’re crafting unique resin art or building a durable, glass-like tabletop, this epoxy offers top-notch results.

Remember to prioritize safety, work within recommended temperatures, and give yourself plenty of time to complete your project.

Have questions or need more advice? Don’t hesitate to reach out—happy crafting!