***Before you start, always remember to wear safety equipment. Working with fiberglass can be hazardous. Safety glasses, latex or vinyl gloves, and a respirator are all important to keeping you safe from the fiberglass and resin. To protect your skin and clothes, wear Tyvek coveralls. Also, you need to work in a well ventilated area.

The first and most important step in laminating (after exercising safety) is surface preparation. Do not skip this step. Use Acetone to wipe down the area that is to be laminated. This removes any dust and grease from the surface.

Cut the fiberglass cloth so that it is a little bigger than the surface that is to be laminated. There are differing of opinions on whether you should cut the fiberglass to the exact shape or if you should cut it a little larger.  We prefer it to be a little bigger. This allows you to fully cover the area to be laminated without worrying about distorting the fiberglass around the edges.

You can use a general purpose laminating resin to laminate the fiberglass to the plywood.  It is used for general fiberglass applications. It cures with a surface tack which helps the multiple layers adhere well to each other.  It also holds the reinforcement in place.  Another benefit to the surface tack is that it is not necessary to sand between layers.  On your final layer, wax can be added (surface agent or surface seal) to the resin.

We measured out 2 ounces of the resin. You can measure out how ever much you need. Next, you will want to use a catalyst quantity chart to figure out how much MEKP you will need to add to the polyester resin.

To add 1% MEKP to 2 ounces of polyester resin, we needed 18 drops of MEKP. The amounts of polyester resin/MEKP does not need to be quite as exact as it would need to be when working with epoxy resin. Using a stir stick, thoroughly mix the resin and MEKP for several minutes. For large quantities, use a power mixer and a drill to speed up the process. Pour a little bit of resin onto your plywood. Using a throw away brush or spreader, spread the resin until it covers the desired surface and there is a nice thin layer of resin on your plywood. Some people let this layer cure as a pre-coat. The pre-coat will seal the wood. The benefits of this layer is that once it is cured, additional resin will not soak into the wood. It will also help to prevent air bubbles. The downside is that the extra resin will add weight and it will take an extra day to complete your project. Once you have applied the thin layer of resin to the plywood, place your fiberglass cloth onto it and allow the resin to soak into the cloth.

It will not completely wet it out so add a little more resin. Again, use your disposable brush or spreader to spread the resin. You can also use an aluminum roller to help completely wet out the cloth and remove any trapped air bubbles Once you do not see any more white from the fiberglass cloth, you know there is plenty of resin. If you see thick spots of resin, you can use your brush or spreader to squeegee it off. You do not want to leave too much resin on your laminate or it will be brittle. But if you leave too little, the part will be weak. Now you let it cure.

During the “green stage', which is after the resin has gelled but before it is fully cured, you can cut off the excess fiberglass. You can do this with a razor blade.

Here is the finished laminate. It is hard and fully cured.

You can also check your left over resin. It should be hard and easily removed from the plastic container. If the resin is hard in some places and sticky in others, the resin was not thoroughly mixed.

For more how to's, information and products go to www.fiberglasswarehouse.com . Save Save

By Dallin Leach 3 comment

Share:

comments (3)

  • Fiberglass Warehouse

    @Pat- You could use the same process you did before but use vinyl ester resin. Vinyl ester resin is much more waterproof than polyester resin.

  • Pat

    Pat: In the past (40 yrs ago) Making aquariums I used a product that took several drops into the resin and fiberglass cloth, then coat with color with added wax, no sanding in between. Now when reading your material it sounds as if polyester resin should not be used due to its strength and water-soluble problems. Yet I do not know what I used then but it was NOT a two-part equal mix resin, and it was not a pure clear resin like the two-part type. The aquarium will be 4’ tall and 3’ feet wide with a Jet canopy for a front resined into the plywood. I made one in the past and it turned out fine and would like to do it again. So my question is polyester resin okay? I have no clue what type it was then. Thanks Pat

  • Jimmy

    I am building 4’x4’x7’tall box out of 1/4” plywood and want to coat it with fiberglass for weather proofing. What type of mat ( and what is the largest size ) and resin should I use. Thinking two coats or three ? Open for suggestions

    REPLY from fgwarehouse:
    I would go with vinyl ester resin and chopped strand mat. Probably 2 layers. You will probably want to paint it or gel coat it also.

Leave a comment

Your email address will not be published. Required fields are marked *

Please note, comments must be approved before they are published

Just added to your wishlist:
My Wishlist
You've just added this product to the cart:
Go to cart page